Every LED video wall is built from cabinets: rigid frames that hold the LED modules, power supply and receiving card, and lock together to form the screen. The cabinet decides much more than people expect. It sets the sizes you can build, how heavy the wall is, how flat the surface looks, how it is serviced, whether it can curve and how quickly it goes up and comes down. Two walls with the same LEDs can behave very differently because of their cabinets.
This guide explains what is inside a cabinet, the common sizes and materials, fixed versus rental designs, service access, and what to check. For walls to compare, see our direct view LED video walls.
What is inside a cabinet
- Frame. The structure that holds everything and locks to neighboring cabinets.
- LED modules. The tiles with the LEDs on the front, usually held by magnets or screws.
- Receiving card. Takes data from the controller and drives the modules in that cabinet.
- Power supply. Converts mains power to the low voltage the modules use.
- Connectors and cables. Power and data in and out, passed along to the next cabinet. Some designs replace internal cables with a circuit board for fewer failure points.
- Cooling. Fans, vents or a fanless design that uses the frame as a heat sink.
Common cabinet sizes
Cabinet size sets the building blocks of the wall. Your wall’s width and height will always be a whole number of cabinets, sometimes with half-height cabinets to fine-tune the size.
| Cabinet size | Shape | Typical use | Notes |
|---|---|---|---|
| 500 × 500 mm | Square | Rental, staging, exhibitions, indoor and outdoor fixed walls | Very common; easy to handle; often paired with 500 × 1000 mm |
| 500 × 1000 mm | Tall rectangle | Rental walls, outdoor screens | Fewer cabinets for tall walls; heavier per piece |
| 600 × 337.5 mm | 16:9 | Indoor fixed and fine pitch walls | Builds 16:9 walls with standard resolutions |
| About 960 × 960 mm | Large square | Outdoor fixed signs and billboards | Fewer pieces for large screens; needs lifting equipment |
| Custom sizes | Varies | Columns, ribbons, creative shapes | Made to fit; check lead time and spare availability |
The cabinet’s pixel count, set by its size and the pitch, decides the wall’s final resolution. See LED display resolution explained for worked examples.
Materials and weight
Cabinet material affects weight, strength, flatness and cost.
- Die-cast aluminum. The most common choice for indoor and rental walls. Precise, light and good at spreading heat. An indoor 500 × 500 mm cabinet is often around 6–9 kg.
- Sheet steel or iron. Cheaper and strong, used mainly for large outdoor signs. Heavier, so structures and lifting plans must allow for it.
- Magnesium alloy and composites. Lighter options used for some rental and touring products.
Total weight drives the structure, rigging and installation method. Always ask for weight per cabinet and per square meter, and include brackets and frames in the total.
Fixed installation versus rental cabinets
Fixed cabinets are designed to be installed once. They focus on slim depth, flatness, quiet operation and ease of service on the wall.
Rental and touring cabinets are designed to be built and struck again and again. Look for:
- Quick locks that join cabinets in seconds without tools.
- Handles and protective corners to avoid damage to LED edges.
- Hanging bars or ground-stack supports for flown and stacked walls.
- Curve locks that set angles for concave or convex walls.
- Flight cases that hold several cabinets safely.
For temporary needs, see our LED wall rental and exhibition LED displays.
Front service and rear service
How a technician reaches the modules, power supply and receiving card changes the installation.
- Front service. Modules come off the face with a magnetic or vacuum tool, giving access to parts behind. The wall can be fixed flat to a building wall with no access space. This is now common for indoor fixed walls.
- Rear service. Technicians work from behind, opening a rear door. This needs a walkway or catwalk behind the screen, but is common on large outdoor signs and rental walls.
- Both. Some cabinets support either method, which gives flexibility.
Flatness, seams and alignment
Viewers notice uneven seams, especially at close range and with flat colors. Good cabinets are machined precisely and have adjustment points so installers can line up each one. On the frame or wall structure, flatness needs to be good before the first cabinet goes up. Ask how the cabinet is aligned and what adjustment is available.
Shapes: curves, corners and creative builds
Special cabinets allow inside and outside curves, right-angle corners, and cubes or columns. Curved walls use cabinets with angle locks or wedge-shaped designs. Right-angle cabinets have bevelled edges so the image wraps around a corner without a gap. Each special cabinet adds design and lead time, so plan these early.
Outdoor cabinet details
Outdoor cabinets carry extra demands. The front face should be IP65 or higher, and freestanding signs need a sealed rear as well. Gaskets, waterproof connectors and breather vents keep out water and limit condensation. Corrosion-resistant finishes matter near the coast. Because outdoor cabinets are often larger and heavier, the structure behind them and the lifting method should be agreed before the cabinets are ordered.
Power, heat and noise
Each cabinet has a maximum and typical power figure. Cabinets are usually daisy-chained for power, with a limit on how many can share one feed. Fanless cabinets are quiet and suit offices, studios and places of worship; fan-cooled cabinets can handle more heat but make some noise. For circuit planning, see LED display power requirements.
What drives the cost
Material, precision machining, service design, rental features and special shapes all affect cabinet cost. Die-cast aluminum costs more than steel, but saves on structure and installation. Custom shapes cost more than standard cabinets, and spares for custom designs should be ordered with the wall.
Checklist: questions to ask about cabinets
- What size is each cabinet, and how does that fit our wall size?
- What is the weight per cabinet and per square meter?
- What material is it made of?
- Is it front service, rear service or both?
- How is flatness adjusted between cabinets?
- Is it fanless, and how loud is it?
- How many cabinets can be daisy-chained on one power feed?
- Can it curve or form corners, if needed?
- For rental, how fast are the locks and how are cabinets protected in transit?
For installation planning, read our LED display installation planning guide and browse more LED display guides. Call 888-631-5880 or contact us to discuss your wall.
FAQ
What is an LED cabinet?
It is the frame that holds LED modules, a power supply and a receiving card. Cabinets lock together to build the full screen.
What is the most common LED cabinet size?
500 × 500 mm is very common for rental and many fixed walls, while 600 × 337.5 mm is popular for indoor 16:9 walls.
How much does an LED cabinet weigh?
Indoor die-cast aluminum cabinets of 500 × 500 mm are often around 6–9 kg. Large outdoor steel cabinets weigh much more.
Do I need front-service cabinets?
If the wall is fixed flat against a building wall with no space behind, yes. If there is a walkway behind, rear service is also an option.
Can LED cabinets build a curved wall?
Yes, with cabinets designed for it. Curve locks or wedge-shaped cabinets set the angle between each piece.