Refresh rate is the spec that matters most when an LED wall meets a camera. To the naked eye, a 1,920 Hz screen and a 3,840 Hz screen can look identical. Point a phone, a broadcast camera or a livestream camera at them and the difference can be obvious: dark bands rolling across the image, flicker, or lines that ruin the shot. If your wall will be filmed, streamed or photographed, refresh rate belongs near the top of your checklist.
This guide explains what LED refresh rate is, how it differs from frame rate and scan rate, what numbers to look for and how to set a wall up for cameras. To browse walls suited to camera work, see our direct view LED video walls.
What refresh rate means on an LED display
LEDs are not dimmed by lowering a steady current the way a lamp dimmer works. Instead, the driver chips switch each LED on and off very quickly, and the share of time it is on sets how bright it looks. This is called pulse-width modulation (PWM). The refresh rate, measured in hertz (Hz), describes how many times per second that on-off cycle repeats.
Your eye averages the rapid pulses into a steady image. A camera does not always do so. Its sensor captures light for a short exposure, often line by line, and if that exposure catches the LEDs in different parts of their cycle, the image shows bands or flicker.
Refresh rate, frame rate and scan rate
Three different numbers get mixed up in sales material:
- Refresh rate (Hz): how often the LED driver cycles each pixel. Typical figures are 1,920 Hz, 3,840 Hz and 7,680 Hz or higher.
- Frame rate (fps): how many new images per second the content contains, such as 24, 30, 50 or 60 frames per second. The wall can display many refresh cycles per content frame.
- Scan rate: how many rows of LEDs share one driver output, shown as a ratio such as 1/8 or 1/32 scan. A higher scan ratio means each LED is driven for a smaller share of the time, which can make high refresh and high brightness harder to achieve together.
When comparing products, ask for the refresh rate at the grayscale depth and brightness you will actually use. Some figures are quoted under the most favorable settings.
What the numbers mean in practice
| Refresh rate | Typical result | Good fit for |
|---|---|---|
| About 960–1,920 Hz | Looks fine to the eye; phone cameras may show bands, especially at fast shutter speeds | Outdoor signs, retail screens, information displays rarely filmed |
| About 3,840 Hz | Generally clean on phones and most video cameras with sensible settings | Churches, conferences, events, corporate studios, trade shows |
| About 7,680 Hz and higher | More margin for fast shutters, slow motion and demanding broadcast | Broadcast studios, virtual production, sports, high-end live events |
The usual rule for anything filmed is 3,840 Hz or higher. For high-end broadcast and virtual production, many teams look for higher rates and test with their own cameras before buying.
Who needs a high refresh rate
- Houses of worship that livestream services. See our church LED walls.
- Broadcast and corporate studios, where the wall is often right behind the presenter. See LED walls for broadcast studios.
- Concerts, conferences and award shows that are filmed for screens in the room and online.
- Rental and staging, where the same wall moves between very different shows. Our LED wall rental page covers this.
- Retail and trade shows, where visitors post photos and videos to social media.
Plenty of screens never meet a professional camera: roadside signs, wayfinding, menu boards. A lower refresh rate is usually fine there, and the saving can go into pitch or size.
Refresh rate and image quality to the eye
Refresh rate is mostly a camera issue, but not only. Some people are sensitive to flicker in their peripheral vision, especially with a large, bright wall at low brightness settings. A higher refresh rate reduces that risk. It also helps keep motion looking smooth when the wall is dimmed, because the driver has more cycles to work with.
There is a link to grayscale as well. When a wall is dimmed, each LED is on for a shorter time per cycle, which leaves fewer steps for shades of gray. Good driver chips keep both high refresh and smooth grayscale at low brightness. That is why a demo at full brightness can be misleading; ask to see the wall dimmed to your real operating level.
Setting up a wall for cameras
A high refresh rate gives you margin, but camera settings still matter. Typical steps include:
- Match frame rates. Run content and cameras at the same frame rate, and use the local video standard where relevant.
- Use sensible shutter speeds. Very fast shutters capture less of each refresh cycle and are more likely to show banding. Adjust in small steps while watching the monitor.
- Synchronise where possible. In studios, the LED processor and cameras can often be locked to a common sync signal (genlock), which removes many artefacts.
- Set brightness for the camera. A wall that is too bright clips highlights and makes presenters look dark. Studio walls often run well below maximum.
- Check for moiré. Fine patterns can appear when the camera’s sensor grid and the LED pixel grid interact. Changing focus, lens or angle usually helps.
Your processor and its settings play a big role here. Our guide to LED display controllers explains the pieces.
What drives the cost
Higher refresh rates depend on better driver chips and careful module design, which add cost. Studio-grade processing with genlock and low latency adds more. The question is whether the wall will be filmed: if it will, the extra cost is usually small compared with a wall that ruins every shot.
Questions to ask before you buy
- What is the refresh rate, and at what brightness and grayscale setting was it measured?
- What scan ratio do the modules use?
- Can we test the wall with our own cameras and shutter settings?
- Does the processor support genlock or frame-rate sync?
- How does the image hold up when dimmed to our normal level?
- Will the same settings work for phones in the audience as well as our main cameras?
For more on specs, browse our LED display guides, call 888-631-5880 or contact us with details of your cameras and space.
FAQ
What refresh rate do I need for an LED wall that is filmed?
A common minimum is 3,840 Hz. Demanding broadcast and virtual production often use higher rates and test with their cameras.
Is refresh rate the same as frame rate?
No. Frame rate is how many new images the content has each second. Refresh rate is how many times per second the LEDs cycle, which is much higher.
Why do LED screens show lines on my phone camera?
The phone’s sensor captures the LEDs at different points in their on-off cycle. A higher refresh rate and a slower shutter speed usually reduce the lines.
Do outdoor signs need a high refresh rate?
Not usually, unless they will be filmed, such as at a stadium or a broadcast event. Many outdoor signs run at lower refresh rates without problems.
Can refresh rate be increased with software?
Only within the limits of the module’s driver chips and scan design. Processor settings can trade refresh against brightness or grayscale, but cannot exceed the hardware.