LED has replaced projection on most stages, from corporate conferences to concerts and festivals. SMD LED panels are bright enough for lit rooms and outdoor shows, can be built to almost any size, and pack into road cases for the next venue. Getting a good result still depends on planning: the right pitch for the room, a safe structure, enough power, and content built for the screen.
This guide is for event producers, AV managers and marketing teams who are specifying LED for a show. If you need screens for a single event, see our LED wall rental options; for a touring kit or permanent stage, look at direct view LED video walls. You can also call 888-631-5880.
How event LED differs from installed LED
Event panels are built to be assembled, struck and trucked over and over. Compared with a lobby wall, rental-grade SMD cabinets usually have:
- Quick locks so cabinets join in seconds without tools;
- Curve locks that set fixed angles for concave or convex screens;
- Corner protectors to guard LEDs at the edges during handling;
- Hanging bars and ground-stack frames designed for that cabinet;
- Light die-cast frames, often 500×500 mm or 500×1000 mm, so crews can lift and pass them easily.
Many rental cabinets can also take both 500×500 and 500×1000 mm sizes in one screen, which gives more flexibility for height.
Pixel pitch by event type
The audience at an event is usually farther away than in an office, so pitch can be coarser. The rule of thumb is about 1 m of comfortable viewing per 1 mm of pitch, and the image stays acceptable to about three times that distance in meters.
| Event type | Nearest viewer | Typical pitch | Notes |
|---|---|---|---|
| Small conference or breakout room | About 2–4 m | About 1.9–2.9 mm | Slides and speaker video need clear text |
| General session or ballroom | About 4–8 m | About 2.6–3.9 mm | Most common for corporate stages |
| Concert or large indoor arena | About 8 m+ | About 3.9–4.8 mm | Size matters more than fine detail |
| Outdoor festival or sports event | About 10 m+ | About 3.9–6 mm, outdoor-rated | Needs high brightness and weather sealing |
Mixed screens are common. A finer-pitch center screen can carry slides and the speaker’s camera feed, while coarser side screens or a low-resolution backdrop add scale.
Brightness and cameras
Indoor event screens usually run well below their maximum, because stage lighting, camera exposure and audience comfort all favor a controlled level. Indoor panels typically top out around 800–1,500 nits. Outdoor event panels need about 5,000 nits or more for daylight shows, and an IP65 or higher rating on the front.
If the event is filmed or streamed, which most are now, refresh rate matters. Look for panels rated at 3,840 Hz or higher and test them with the actual cameras. Shutter speed and frame rate can still cause scan lines, so the video team should check the screen during setup. For LED used as a backdrop behind presenters, a slightly finer pitch and a matte surface help avoid moiré patterns on camera.
Structure and rigging
There are two ways to put a screen up:
- Flown: hung from truss or venue rigging points with hanging bars. It keeps the floor clear and suits large screens, but needs a qualified rigger, rated points and a load calculation.
- Ground-stacked: built up from the floor on a base frame with rear bracing. It suits venues without rigging and smaller screens, but needs a level floor and ballast or bracing against tipping.
Either way, weight adds up quickly. Ask for the weight per cabinet and per square meter, add the frames and cabling, and get the structure signed off. Outdoors, the wind load decides how big a screen can safely be and when the show has to stop. Agree a wind plan with the rigging team before the event.
Power, signal and control
Event LED needs clean, distributed power. Panels list maximum and average consumption per cabinet; size the distro on the maximum. Run power and data in loops so a fault affects as few cabinets as possible, and carry spare cables.
The signal path usually runs from a media server or switcher to an LED processor, then by network cable or fiber to the screen. The processor handles scaling, color and brightness, and can split one image across several screens. Long cable runs between front of house and the stage often need fiber. Build in redundancy for important shows: backup processor, dual signal paths and a spare playback machine.
Load-in, show and strike timeline
- Advance: confirm screen sizes, rigging points, power, load-in times and content specs with the venue.
- Load-in: unload, assemble frames, hang or stack cabinets, run power and data.
- Setup: map the screen in the processor, check for dead pixels, set brightness and color.
- Content check: play every file and live input on the real screen, with cameras running.
- Show: a technician stays on site with spare modules and tools.
- Strike: take down, pack cabinets in their cases and check for damage.
A medium corporate screen is often built in a few hours. Large concert or outdoor screens can take a full day or more, so plan the venue access accordingly.
Content specs for event screens
- Get the exact pixel resolution of each screen and build content to it.
- If the screen is a non-standard shape, use a pixel map template from the LED team.
- Keep slide text large; a common mistake is dense slides that cannot be read from the back.
- Use dark or mid-tone backgrounds on backdrops behind presenters so faces stay well lit on camera.
- Send final files early and bring backups on a separate drive.
Questions to ask your LED provider
- What pitch do you recommend for this venue and audience distance?
- Is the screen flown or ground-stacked, and who signs off the rigging?
- What is the refresh rate, and have you tested with our camera package?
- What power do you need, and where must it be delivered?
- What is the signal path, and what redundancy is included?
- How long are load-in and strike, and how many crew?
- Will a technician stay for the show, with spares?
For more on event screens, read our guides to LED video walls for live events and LED video wall rental. Browse all our LED display guides, or contact us with your venue and dates.
FAQ
Should I rent or buy LED panels for events?
If you run a few events a year, renting is usually simpler. Production companies and venues that use screens often may find buying a kit makes sense over time.
Can event LED screens be curved?
Yes. Many rental cabinets have curve locks that set fixed angles, so screens can wrap a stage or form arcs and columns.
What pitch is best for a corporate conference?
For a typical ballroom general session, about 2.6–3.9 mm is common. Breakout rooms with closer seating may need finer pitch.
Why do LED screens flicker on camera?
The camera’s shutter can catch the LED refresh cycle. A refresh rate of 3,840 Hz or more and matching camera settings usually solve it.
Can LED be used outdoors at festivals?
Yes, with outdoor-rated panels that have high brightness and weather sealing, and a structure designed for the wind conditions.